Dual Reflex Camera

My Dual Reflex camera.

This week's camera is very low-tech and a follow-up to a series of cameras I discussed in a past article on the Lark and Kandor "Sardine Can" cameras two years ago. 

 I found this camera in a display, hidden behind other cameras, at a local camera store many months ago. I recognized the camera from a previous article, and it was a different style of camera from before. This was a "twin lens" style camera, but made by the same company, Irwin Corp of New York. 

 As I was discussing the camera with a store staff member, they said it was for "display only" and not for sale because it wasn't working. I told the salesperson that I had written an article on this camera style and wasn't worried about whether it worked, but just wanted it for my collection.

 I enquired further about the camera, the salesperson said they needed to ask the owner whether he would sell it. I encouraged the salesperson to inquire. Upon their return, they said the owner would indeed sell the camera and gave me a reasonable price to purchase it,  especially since the camera was in rough condition and I was told the shutter was not working. The shutter wasn't dead. It did open and close, but it was extremely sluggish.

 All of the leather was also on the camera, though it was coming up at the edges due to shrinkage and having been dried out for many years. The fact that the leather was still there was another good reason to purchase the camera, as I could recondition the leather and tack it back into place, giving the camera the care it deserved.

 As I paid for the Dual Reflex camera along with some discounted, recently discontinued film, I left the store with a new acquisition, knowing I'd fix it up and write an article about it at some point.

 Looking over the shelf to do this week's article, I saw the Dual Flex, and figured since I did an article on the Konica Pearl last week, which has an integrated rangefinder in a folding 645 format. Let's lean the other way this week and do a lower-end, Lomography-type camera from the early 1950s.

 One thing I needed to do before writing about the Dual Flex was to fix the shutter and clean the camera as best as I could. The repair was extremely simple, as the entire shutter assembly was held to the camera by two screws, one on top and one on the bottom. Then, to get to the shutter itself, two other screws on either side of the lens held the cover on. 

 Once the cover was off, the entire assembly consisted of a simple spring-loaded box-camera-style shutter that needed general cleaning and lubrication. There is also a lever that changes the aperture setting, which already moved smoothly, so I didn't do anything with that. 

 While the shutter was out, I cleaned the inside of the lens and reassembled it, making sure it was functioning as it should. With a "snappy" shutter in working condition, I screwed the cover back into place and mounted the shutter back onto the camera. Double-checking that the shutter seemed to be working after reassembly, I was now ready to write the article.

History:

 Irwin Corporation of New York occupies a curious and appealing corner of toy and camera history. Best remembered by collectors for its inexpensive metal cameras and low-cost toys, the company seems to have specialized in simple, playful, and affordable products. One surviving description notes that Irwin began by manufacturing 127 roll-film metal cameras resembling sardine tins, priced at just $2.98, which immediately places the firm in the world of budget photography novelties rather than serious camera manufacturing.

1948 advertising for Irwin Corp.

 That detail helps explain why Irwin still draws attention from vintage camera collectors today. These were not precision instruments meant to compete with the major camera brands. Instead, they were novelty cameras designed to be accessible, fun, and inexpensive enough to appeal to casual buyers. In that sense, Irwin's cameras belonged to the same broader culture as dime-store toys and impulse purchases: small objects that offered a quick thrill and a modest introduction to photography.

 Irwin also appears to have expanded its production to include toys, especially metal toys and, later, plastic items. Collector references suggest that the company produced cars, trucks, and other small playthings and continued to produce toys well into the 1950s and 1960s. By the mid-1950s, the company was said to have plants in Fitchburg and Leominster, Massachusetts, and Nashua, New Hampshire, indicating that it had expanded beyond a single New York address.

 The surviving record also suggests a company that adapted with the times. A 1964 dealer catalog reportedly included toy cars for Ken and Barbie, along with plastic GI Joe vehicles, which shows how Irwin followed the changing market for licensed and character-based toys. That flexibility likely helped the firm remain relevant in a crowded and fast-changing industry.

 Today, Irwin Corporation is remembered less as a major manufacturer than as a fascinating specialty producer whose history bridges toy collecting and camera collecting. Its sardine-tin cameras and inexpensive metal toys make it a small but memorable part of American mid-century design.

My Camera:

 My Dual Reflex camera is 3" wide by 3" deep and 5.25" tall when the viewfinder is closed, and 6.5" tall when the viewfinder is extended and opened for viewing. The camera weighs 14.8 ounces without a roll of 127 film loaded.

As previously mentioned, the camera has a very simple, spring-loaded shutter with only one speed, which I'm guessing is around 1/100. That may be too generous and could be even slower; that's my guess. The shutter control has only two options—either Instant for standard snapshots or Time for longer exposures. A switch on the side of the camera controls this. Since the shutter is so simple, the "time" setting blocks the shutter from moving into the "open" position until you release the lever; then the shutter closes.

 The shutter release is located at the 11:00 position on the lens cover and is nothing more than a lever that activates the shutter's spring mechanism.

 As you look at the camera from the front, the aperture controls are just to the left of the lens. They are controlled by a lever that moves a group of openings on a metal sheet back and forth across the lens opening. The aperture settings are F/7.7 (maximum), F/11, F/16, and F/22. There is no focus control on the lens, as it's set to the standard 8 to 10 feet, and the camera's aperture controls the sharpness.

o pop up the viewfinder, lift the rear of the finder, and the viewfinder or light chimney pops open, exposing the ground glass. Since there is no focus control on this camera, the viewfinder is used only to compose the image.

 An interesting option on the Dual Reflex camera is the ability to use a pseudo-eye-level finder for composing photos. On the back of the light chimney is an optical finder that, when viewed through, looks into another optical opening on the front of the chimney, allowing the photographer to use it as an eye-level finder rather than a waist-level one. For an inexpensive camera, this is a nice feature and actually works well.

To close the viewfinder, close the back compartment first since it has the optical glass, then the sides, and the front last. If you try to do it the conventional way and do the sides first, the front won't close because the glass is pressing up against the side wall, leaving the front no room to close.

 To take the back off to load film into the camera. On the back, the top is a large knob that must be unscrewed to remove the back. Once removed, you'll load the 127-size film, similar to any other roll-film camera. Put the fresh, unexposed film in the bottom area and the take-up spool on the top, right-hand side of the camera, where the winding lever is located. Bring the leader to the take-up spool, thread it into the slot, and wind until you see "start" on the paper backing. Close the back of the camera and screw it on tightly. 

 Since this is a 3x4cm format frame and the camera has two red windows, you'll wind until you see the number 1 in the first window. Take your photo, then wind until you see the number 1 in the second window, and take your photo. Follow this process through the number 8, meaning you've taken 16 images on the roll of film. Take the film out and process it.

The only 127 film I currently have is a few rolls of Jessop black-and-white film I purchased at the Tokyo City Flea Market a few months ago. The expiration date on the film is 11/1999. I hope it's still usable. 

 Now that I have the shutter fixed, lenses cleaned, and film loaded in the camera. It's Time to walk the neighborhood, taking photos to see how the Dual Reflex will perform.

 My Results:

 As I walked through the neighborhood, I tried using both the eye-level and waist-level finders to see which I preferred. They both were easy to use, so here are the results from my walk.

Conclusion:

 Well, some of the images turned out better than expected, and others didn't turn out the way I expected. There is a lot of debris on the negatives, which I'm guessing is due to the film's age.

 The film is rated at 200 ISO, and with its age, I wasn't really sure about the exposure, so I tried to take a couple of shots of the same subject at different aperture settings. I'm not sure why it happened, but there is tremendous bleed-through from the paper backing onto the film, creating issues with the images.

 After I processed the film, I took a closer look at the red windows on the back of the camera, which I believe caused the bleed-through from the paper backing. Yes, one of the red windows appeared to be OK, but upon closer inspection, it was pushed in, letting white light in. I found the culprit behind the bleed-through issues with the film.

 The camera handled well, the viewfinder was somewhat bright, and I enjoyed using the eye-level finder for composing the photo. The image sharpness is what I expected, especially for a very low-cost camera made around 75 years ago. 

 Thank you for taking Time from your day to read about this Lo-Fi camera made in the early 1950s by a company that not only made metal toys but also a line of cameras, mainly known for the "Sardine Can" cameras.

 Here are my other Camera Reviews.

 Cuny's Camera and Photos is my online eBay store where you can find some of the previously reviewed cameras for sale, along with other cameras, lenses, and photo oddities I've accumulated over the past 50 years of collecting.

 Until next week, please be safe.

Mizuho Six camera

My Mizuho Six camera & case

During my trip to Tokyo a month or so ago, one of my primary goals was to find a little-known or unusual camera to write about for this camera-collecting blog.

 It was on my last day in Tokyo that I visited Used Camera Box for the second time. To say this camera store is filled to the rafters is beyond description. Most of the camera stores I visited in Tokyo were well laid out, with space between cameras. All the items with tags and prices are very visible. It's very similar to what you'd see in any city in the world, with cameras or other products displayed. 

 The Used Camera Box is unlike most camera stores you'll come across.  The shop is pretty small, but the amount of cameras they have is unbelievable.  Many of the showcases featuring the higher-priced, most desirable cameras are well displayed. 

 Then there are other areas of the store with showcases with cameras on top of cameras, on top of cameras. Stacked three high and so crammed next to each other, it's difficult to see what they have towards the back of the showcase. 

 There are the bins, many, many bin of cameras. All around the store's perimeter are tall showcases. In front of these tall showcases are plastic bins filled with more cameras. Many of the cameras in these bins are "bargain" items, which means they might have a part missing or not work. These bins are stacked three high, going around much of the store. Because of this, it's probably one of my favorite used camera stores. 

Name on top of the camera below the shutter release

 For me, the real pleasure of collecting is the hunt. The excitement of finding a real odd or unusual item at a bargain price. It's similar to going to a Flea Market, as there may be a real treasure in the next cabinet or stall. 

 I worked my way to one of my favorite showcases towards the back of the store. It's a showcase filled with many of the older cameras. It has a mix of higher-priced and lower-priced items. The patient salesperson let me pull items out and check them out. It was from this showcase that I found this week's camera, the Mizuho Six. The camera comes with a nice leather-fitted case, too. This, along with last week's Baron RI, was another camera I had never heard of until I researched it.

 Just like last week's blog about the Baron RI camera, this week's camera is another very similar style. It's a folding 120 camera made in the early 1950s, when Japan was rebuilding after World War II. 

 It was manufactured by another, smaller, and little-known company that later changed its name to Neoca. Here's some history on the brand.

History:

 The Mizuho Six began life in the early 1950s, when Mizuho Koki of Japan was producing folding medium-format cameras for a market that still valued compactness and simplicity. These early Mizuho-branded folders used 120 film and reflected the practical, postwar approach common among smaller Japanese camera makers.

From my book on collecting Japanese Cameras

 In 1954, the company changed its name to Neoca, and the Mizuho Six line became part of that transition. The name change marked a shift from the earlier Mizuho identity toward a broader Neoca camera range. At the same time, the foldable medium-format design remained rooted in the company's first postwar products.

 The Mizuho Six itself went through a series of small but meaningful variations rather than a dramatic redesign. Known versions include the Mizuho Six I, II, III, IIB, IIIB, and V, as well as later Super models such as the Super, Super N, and Super T. These changes suggest the camera was gradually updated with different body details, finder arrangements, and lens or shutter combinations.

 The best-known early version, such as the Mizuho Six V a, was a folding camera that offered either 4.5x6 or 6x6 cm exposures and used an uncoupled rangefinder. That combination made it a flexible, straightforward tool for photographers who wanted medium-format image quality in a portable body.

 As Neoca moved into its own identity after 1954, the company shifted increasingly toward compact 35mm cameras. Still, the Mizuho Six remains important as a bridge between eras. It represents the company's early craftsmanship and the transitional period when Japanese manufacturers were moving from traditional folding cameras toward the more modern designs that would dominate later in the decade.

My Camera:

 Built in the early 1950s, my Mizuho Six camera is 5.5" wide, by 4" tall, by 2" deep with the lens closed, and 4" deep when the lens is extended into the taking position. The camera weighs 1 pound, 7 ounces without film loaded. The camera's serial number is 3391. The camera also has "Made in Occupied Japan" embossed on the side where the film door release is located.

To open the lens to take a photo, depress the small button on top of the camera located in front of the accessory shoe, and to the right of the film winding knob. Once depressed, the lens board opens, exposing the lens.

 The Mizuho Six has an 80mm Mizuho Kiko Miltar Special F/3.5 lens, serial # 2664, in an NKS shutter. The shutter speeds range from 1/200 to 1 sec, along with "B" for timed exposures. The shutter speed is set by turning the shutter speed dial around the lens to the desired speed. The shutter release is located on the top, right side of the camera, just in front of the "Mizuo-Six" name and serial number.

 The aperture is set similarly by sliding a knurled ring around the lens to the desired aperture, which ranges from F/3.5 to F/22.

It wasn't until I shot my first roll of film through the camera that I realized the shutter wasn't working properly, so I'll need to either get it fixed or sell the camera with the defect. The issue is when I cock the shutter, which is done with a small switch on the top of the lens, the shutter remains open until you depress the shutter release. It doesn't really "cock" the shutter as it should. 

 What I did notice was when I pulled the shutter cocking ever over to the farthest position, the shutter wouldn't open. It was when I released the lever after the cocking maneuver that the lens stayed open. If I pulled the lever all the way, held it, and then tripped the shutter release, the shutter would work as intended. This was awkward to use this way, but it's the method used to take the blog images.

 There is no rangefinder in this camera; it has only an optical viewfinder on top to frame your images. To focus on the subject, rotate the lens manually to the "guessed" distance to your subject before taking the photo.

 To close the camera for transport, depress the two enlarged tabs on the camera's struts inwards. The lens board will collapse, and you can close it back onto the camera body, which will lock it into position.

The one interesting feature of this camera is the ability to shoot either 6x6cm or 6x4.5cm. When you open the back of the camera to load film, there are two "wings" that can be pulled up from each side of the film chamber, covering a portion of the taking area and thus cropping the frame size from 6x6cm to 6x4.5cm.

 Once you make the change, you'll then use the appropriate red window on the back of the camera to count the frame numbers imprinted on the 120 rolls of film. It will also give the photographer four more images per roll, going from 12 images on a 6x6cm format to 16 on a 6x4.5 format camera. You'll need to shoot the entire roll in that format, as there's no way to change formats mid-roll.

You load the camera as you would any roll-film camera, with the take-up spool on the left side. Load the fresh roll on the right, and bring the film's leader to the take-up spool on the left,  making sure the leader is in the take-up spool. Then wind until you see the "start" arrows pointing outwards. Close the back of the camera and wind the film until you see the number 1 in the red window for the format you're using.

 Now that we have film loaded into the camera, let's take it out and see what results we get.

 My Results:

 Opening the Mizuho Six and cleaning both the front and rear elements of the lens before loading the camera. I had some T-Max 100 film that was just about out of date, so I loaded it into the camera. I chose the 6x6cm format so I could use a larger image size and assess the lens's sharpness.

 Here are the results from my walk around the neighborhood with the Mizuho Six camera

Conclusion:

 Well, I think the second roll of film turned out much better than the first roll, but I'm not overly impressed with the sharpness. This could be from a couple of different factors.

 While I cleaned the lens as best I could, it still seems to have some haze. The second factor is that the lens is slightly out of registration. I'm a fairly good guesser of distance, and the lens even at infinity seems a bit out of focus. I also think that some of the issues with the focus were caused by camera movement and what I needed to do to operate the shutter.

 The camera also has cosmetic issues. Some parts of the leatherette are missing and can be easily replaced. Given the shutter issues and the lenses' haze, this may not last long in my collection, and you'll probably see this in my online store soon.

 On the plus side, the camera can shoot in different formats, which is a nice feature, but I don't think it's going to overcome the camera's faults. It's a fun camera to shoot with, and I was happy to learn more about this camera.

 Thank you for taking some time from your busy day to learn a bit about this little-known camera from the beginning of the Japanese camera revolution.

 Here's a link to my other Camera Reviews.

 Cuny's Cameras and Photos is my online eBay store where you'll find some of the cameras I reviewed for sale, along with many other cameras, lenses, and photo items from my collection.

 Until next week, please be safe.

Ebner camera

My Ebner 6x4.5cm camera

During my trip to Tokyo, Japan, a couple of weeks ago, I was in Kitamura's flagship store, looking at their "bargain" cameras, which in itself is a treasure trove of used cameras, when I spotted a brown Bakelite camera sitting on one of their shelves. The camera was a "folding" style camera. Still, I had never seen a camera like it, so immediately I wanted to see it, and with any luck, take it home with me, provided the price wasn't outrageous. I scanned the camera price and converted it from Yen to US dollars; it wasn't outrageous, so I wanted to see it and learn more.

 The things that caught my eye at first was the beautiful, rich brown color, the wonderful pebbled texture of the body, and the very sleek design. To me, the camera just sang to me in its design. Since my eyes almost always go to anything "colored" when I look at cameras, it reminded me of the Coronet Vogue. Then, scanning the shelf below, they also found the Coronet Vogue. which I had seen in a few different flea markets in both Paris and London, but the asking price was always too high (in my opinion) for the camera, so I passed them up.

Back side with beautiful pebble finish on the Ebner camera

 At this point in my camera search, there were 3-4 cameras I wanted to look at, so I went up to one of the salespeople on the floor and showed them the items I was interested in. Very patiently, he pulled the 4 items from the shelves and placed them on a camera mat on one of the glass display cases in the shop.

 Opening the Ebner camera first, I hadn't seen it before and don't recall it in McKeown's Camera Guide. I don't have the few hundred thousand cameras memorized. It wasn't until I opened the back of the camera and noticed the name "Ebner" that I realized the camera's brand. It still hadn't jogged my memory or sounded familiar.

Similarities of the Ebner and Coronet Vogue cameras.

 As I looked over the camera, the shutter worked, the aperture slid around the lens and changed size, and the lens was fairly clean. It didn't have mold, mildew, or fungus as I shone a penlight through the lens, and I didn't see pinholes in the bellows, so all in all, the camera was a "keeper" to me.

 The Coronet Vogue camera had some issues. It had a replacement black bellows rather than the original brown matching bellows, and the side struts of the camera didn't work properly. But the camera was inexpensive, and the shutter worked, so I believe at some point later this year I will write about it. To me, the similarity in the design and style of both the Ebner and Coronet Vogue cameras is striking.

 The similarities make sense to me, especially since Ebner stopped producing cameras in 1935. Still, other camera companies, like Pontiac and Gallus, produced very similar cameras with the same sleek design. I'm confident that since the Coronet Vogue was introduced in 1936, they recognized that this sleek, Bakelite camera design would benefit their sales, and they produced it.

History:

 Albert Ebner & Co. was a small but interesting German manufacturer that moved from audio and electrical products into cameras during the early 1930s. Albert Ebner, born in 1891 in Bad Cannstatt, had already founded earlier companies before his name became associated with the camera firm that collectors remember today.

Portrait of Albert Ebner

 The company's background was in turntable motors, gramophone parts, and related household electrical goods. After earlier business setbacks and reorganizations, Ebner returned to Bad Cannstatt and formed a new Albert Ebner & Co., often abbreviated AECO, which broadened into vacuum cleaners, fans, and other electrical products before experimenting with cameras.

 Ebner's camera output was very limited. The firm produced only two folding models: a 6x9 cm camera on 120 film and a smaller 4.5x6 cm model on Kodak 620 film, both made around 1933 to 1935. These cameras had no special model names beyond their image size, which makes them especially plain in naming but distinctive in construction.

 What set them apart was their design. Both cameras used a marbled brown Bakelite body, a material associated with the radio and record-player industries, and they paired that shell with a Compur leaf shutter and lenses from makers such as Meyer-Gorlitz. That gives the Ebner cameras a streamlined Art Deco look that feels more industrially designed than mass-market consumer.

German advertising.

 The larger 6x9 version used standard 120 film, while the 4.5x6 version used 620 film, an unusual choice for a German maker of the time. Collectors also note that the cameras were sold mostly in Germany and that production was brief, with the company apparently ending camera manufacture by 1935. Because so few were made, surviving examples are relatively scarce today.

 Ebner's camera venture did not last long. Still, it fits a broader pattern of early 20th-century firms adapting existing expertise in Bakelite and mechanical assembly to camera production. After the camera period ended, Albert Ebner's business life continued in audio through the later Perpetuum-Ebner merger. In contrast, the cameras remained a short-lived sideline that now attracts collectors and historians.

My Camera:

 My Ebner 6x4.5cm camera is 4.25" tall with the retractable viewfinder down, and 5" tall with the viewfinder in the upright, viewing position. It's also 5.5 wide and 1.25" deep with the lens retracted, and 4" with the lens extended and in the normal taking position. The camera weighs 1 pound 0.7 ounces without film loaded inside. 

To open the Ebner camera, on the top of the camera is a button between the retractable front viewfinder, which pulls up from the camera body to produce a vertical rectangle. and a small pbar with a ball on the end used as the rear portion of the viewfinder. This bar is also retracted into the camera body. Once the button is pressed, the front door housing the lens, bellows, and shutter springs from the camera body.

The Ebner I own has a Meyer-Goerlitz 7.5cm F/4.5 lens (SN 625604), with a Compur shutter, ranging from 1/300 to 1 second, plus "T" and "B". There were several different lens and shutter combinations for the camera. The aperture range is from F/4.5 to 22. 

 Setting the shutter speed is done by turning a ring on the outer portion of the lens, and the aperture is set by sliding a lever with a pointing end to the desired aperture setting under the lens. Also, the shutter is cocked by one lever at the top of the shutter and released by another lever on the side of the shutter. Focusing the lens is done by rotating the lens itself to the desired focus distance in meters, as seen on the top of the lens.

To close the camera for transport, there is a bar at the bottom of the lens bed, just in front of the "Ebner" plate. Press these bars towards the camera body; the lens board releases, allowing you to tilt the board back up and into the camera body. It will click when the lens board is locked into position.

Opening the film back to load film is done by sliding the locking lever, which is located under the camera's strap. Once unlocked, you can slide the door open to reveal the camera's film chamber. Once opened, you'll see the vertical format 6x4.5 film area. The new film goes on the right side of the camera, and you'll transfer the empty spool from the right side to the left, where the film's winding wheel is located. My camera didn't have an empty spool, so I needed to supply the camera with one.

  Looking at the film holders' pins, the camera takes 620 film, but I accidentally loaded the camera's take-up chamber with 120 film, and it fit. Generally, when I try to put 120 in a 620 camera, the spools don't fit, or they don't turn because the pins are too small to grab the 120 spool. Let's see if I can load a roll of 120 film in the camera. Interestingly, this camera: the 120 film fits a bit snug, but the film advance engaged with the spool, and the film wound smoothly.

Since the camera is 6x4.5cm, with two red windows on the back, this symbolizes that you start with the number one in the first window, take your photo, and then wind the film until the number one shows up in the second window. You do this with the whole roll, which ends with the number eight showing in the second window, giving you sixteen images per roll of film.

 Once the film was loaded in the camera and the "start" arrows were showing, I closed the back of the camera, and my daughter, her dog, Bean. I went for a walk along the Columbia River and took photos with the camera. The camera is very "pocketable" and travels extremely well.

 Let's see how the images turned out.

 

The Results:

 The results aren't bad, but not the sharpest images either, especially compared to the Kolar Kola camera. I may have missed the focus distance, but most of the photos are sharp enough for an 8x10. Here are some of the images I took while walking the Columbia River with my daughter and Bean, her dog. 

Conclusion:

 There are several things I really like about the camera. Still, the thing I enjoyed most about this camera is its thinness when traveling. It's so thin compared to other medium-format cameras; for me, it makes it fun to use. Not being bulky or clumsy and being fairly lightweight make this camera a real pleasure to carry around.

 The brown pebble finish is also a bonus in my opinion, adding more to the camera than leather and chrome alone. It has a very appealing feel and firmness that make the camera fun to hold.

Designers in the 1930s were still in the Art Deco period. They had a real sense of classical design, which they implemented in their products. It makes me even more want to buy a 3D printer to experiment with designs and textures, which I feel are lacking in today's designs.  

 Thank you for taking the time to learn a bit about this very classic and rare camera made in Stuttgart, Germany, in the early to mid-1930s.

 I'd love to hear from you, so if you have a comment or one of your own, please share it with us here.

 Here are my other Camera Reviews.

 Cuny's Camera and Photos is my online eBay store where you might find one (or many) of the cameras I've reviewed, along with other camera and photo items I've picked up or hoarded over the many years in the business.

 Until next week, please be safe.

Kolar Kola camera

My Kolar Kola camera

I didn’t write a blog post last week because I was in Tokyo camera shopping and hoping to find something odd and unusual to write about in the coming weeks. I was successful in that search, and this week’s camera is one I bought at one of my favorite used camera stores in Japan, Kitamura Camera in the Shinjuku area of Tokyo. Kitamura has several locations, but this was their flagship store.

 Kitamura Camera is an impressive multi-floor store with just about everything a camera lover could want, from a photo studio to film sales and processing. The most impressive parts for me were the two used-camera floors. The fourth floor had an outstanding collection of rare Leica cameras and lenses, Nikon rangefinders and lenses, Hasselblad gear, and other medium format cameras and lenses. The third floor was where I spent the most time. That was their bargain floor, with many lesser-known cameras and others that were not quite perfect.

 They also had Leicas and Nikons there, but some had small defects or were not fully functional. These were not the kind of “junk” cameras you often see in used camera stores, where lenses have fungus and shutters no longer fire. These were cameras most people would probably buy for parts, but Kitamura still presented them in a much more appealing way.

 That third floor is where I found this week’s camera: an odd cube-shaped camera called the Kola. I had never heard of it before. When I checked it out, the lens was clean, the shutter fired at all speeds, the film spools were still in the camera, and the price was very reasonable.

Back side of my Kolar Kola camera

 At first glance, I thought it might be a 127 film camera because of the film spools, but the frame size was marked 24 x 36, which meant it was a 35mm camera. That made me think it may have used paper-backed 35mm film, similar to the way some Bolta cameras were loaded.

It was certainly unusual enough to catch my attention, so I bought it along with a few other treasures from the shop. I planned to do the research later, but for the moment I set it aside and kept exploring the store. I knew I would be back before leaving Japan.

 Later that day, back at my hotel, the first camera I pulled out was the Kola. I wanted to know more about it right away. I soon learned that the camera was made in Czechoslovakia by a small and relatively obscure camera maker in the 1930s.

 Many examples I found online show Kola cameras in a 4 x 4 cm format on 127 film. Some earlier versions have a barrel lens, and the lenses I found were usually marked f/3.5 or f/4.5. I also found references to a paper-backed 35mm version. In my research, I saw that some Kola cameras used special 35mm cassettes and a different geared spool, but that spool arrangement did not match the camera I own.

 Here is a little more about the maker.

History

Václav Kolář was a significant, if short-lived, figure in prewar Czechoslovak camera manufacturing. Based in the Modřany district of Prague, Kolář operated his workshop during a period of experimentation and innovation in European photography. In the 1930s, small makers like Kolář were trying to compete with German giants such as Zeiss Ikon and Voigtländer.

 Kolář’s history appears to have been one of rapid innovation followed by financial difficulty. His company focused on precision engineering and often produced cameras that were mechanically sophisticated for their price point. However, the economic pressure of the Great Depression and fierce competition from Germany eventually led to bankruptcy in the mid-1930s. Today, his cameras are considered hidden gems of Central European camera history, prized for their rarity and distinctive design.

 His product line was surprisingly varied for such a small workshop. One of his best-known cameras was the Kola-Diar, a box-shaped roll-film camera. It was designed to be compact and practical, often using 127 film or unperforated 35mm film, which later gave it a bit of a spy-camera reputation among collectors. It featured a collapsing lens mount and a rugged build that stood out from the folding cameras of the period.

 Another notable model was the Kola-Flex, a twin-lens reflex camera made largely of Bakelite. Unlike many pseudo-TLR cameras of the era, the Kola-Flex often featured gear-linked lenses, allowing for more accurate focusing through the top viewfinder. Kolář also produced the Kolex, a traditional folding plate camera, and the Box-Reflex, an entry-level Bakelite model. These cameras were typically fitted with lenses bearing Kolář’s own names, such as Rekolar, Kolyt, and Kolar-Anastigmat, and were often paired with reliable German shutters like the Vario or Compur.

 Kolář’s legacy lies in his pioneering work in the Czech tradition of fine mechanical camera building. His designs showed that Czechoslovak workshops could produce serious photographic equipment, helping lay the groundwork for the later nationalized industry that would produce the Flexaret series.

My Camera

My Kolar Kola camera measures 3.5 inches wide, 3 inches tall, and 2.75 inches deep. It weighs 1 pound, 1.7 ounces, and has serial number 740 stamped into the back of the camera. It is fitted with a Schneider Xenon 5cm f/2.9 lens in a Comur-Rapid shutter. The shutter speeds range from 1/500 second to 1 second, with T and B settings for timed and bulb exposures. There is a cable release socket next to the shutter cocking lever on the top of the shutter, and the shutter release is positioned low at about the 8 o’clock position.

In my research, I found that many Kola cameras use a helical focus system mounted behind the shutter mechanism, but mine is a front-element focus model, meaning the lens itself rotates. Focus distances are marked on the outer ring of the lens in meters.

On top of the camera, from left to right, there is a large winding knob that advances the film clockwise. In the middle is a very small optical viewfinder, which is especially hard for me to use since I wear glasses. To the right of that are two small raised openings that can accept a cold shoe, much like the Nagle Pupille camera. An accessory rangefinder can be mounted there for critical focus.

 To the right of the cold-shoe area is the frame counter, located inside the knob that holds the film in place. Behind the frame counter is a small round indicator attached to the wheel inside the film chamber. As the film moves across that wheel during winding, the indicator turns, and each full rotation advances the frame counter.

The more I look at this camera, the more similarities I see between the Kola and the Nagel Pupille camera. Both have helical-focus variations, both offer an accessory shoe for a rangefinder, and both have a solid, well-made feel.

 To open the back and load film, there are two clips on either side of the camera that hold the back to the body. Pull those clips back, and the rear cover slides off, exposing the film chamber.

This is where the camera becomes especially interesting. There were already two spools inside, and they were just a little shorter than a 127 spool. The exposed frame area is 24 x 36, so the camera is definitely a 35mm model. My first idea was to use 127 backing paper with bulk-loaded 35mm film, but when I tried the 127 spools, they actually fit into the camera. Not perfectly, since the winding and holding knobs sit slightly higher, perhaps by about 1/16 inch, but they did fit.

I removed the 35mm spools that came with the camera and loaded it with 127 film I already had. On the back of the camera there is a red window, so I hoped I would be able to see the numbers pass by as I took pictures. If not, I could use the frame counter and the rotating wheel to estimate the proper spacing for 35mm-sized exposures on a roll of 127 film. I knew there would be some waste because the 127 film is wider than the image area the camera is using.

On the bottom of the camera there is a hinged door that allows the spools to be inserted into the body. The 35mm spools that came with the camera are too wide to fit through that opening, so if I were to use paper-backed 35mm film, I would need to open the hinged door to get the spools inside. The door is secured by a sliding latch that locks it in place.

Once the 127 film was loaded, I slid the back onto the camera body, latched the two clips, and headed out to make some photographs.

Results

With a roll of 127 film loaded, I walked through the neighborhood taking photos of the usual subjects to see how the Kola performed. At first, I guessed at the distance between frames, and that worked well enough. The frame counter behaved exactly as expected.

 Here are the results from my neighborhood walk.

Conclusion

WOW! I was very impressed with the sharpness and ease of use of this camera. The viewfinder is small and a bit difficult to use, especially for me since I wear glasses, but the sharpness of the images and the smooth film advance made up for the camera’s quirks.

 It would have been better to shoot 35mm film, since that would have avoided wasting image area the way 127 film does here. However, the hassle of paper-backed 35mm film, plus the unusual spool setup, made the wasted film area easier to accept.

 I am still puzzled by this particular Kola. It has a faster f/2.9 lens than the f/3.5 or f/4.5 lenses I found in my research, and it is also a 35mm version with spools that differ from those that came with the camera. That mystery makes it even more interesting to me.

 I am really happy with the results this Kola camera produced, and I am glad I found such a special camera on my trip to Tokyo.

 Here are my other Camera Reviews.

 Stop by Cuny’s Cameras and Photos to see what I have for sale in my eBay online store. It is filled with camera accessories, and you may even find a camera or two that I have reviewed in the past.

 Thank you for taking the time to learn about this small powerhouse of a camera made by a company in Czechoslovakia for such a short period of time. I am very happy to have one in my collection.

 Until next week, please be safe.

 

Welta Superfekta

My Welta Superfekta camera

Not being wealthy, my collecting has always been focused on cameras well within our family's financial means. Up until my final ten years of working and before retirement, the cameras I purchased were items you could find at local flea markets and estate sales, or occasionally I made a trade for an item while selling at a camera show where I had a table.

 Being drawn to obscure and unusual cameras and having devoured McKeown's Camera Guide for many years, the Welta Superfekta is one camera I've always dreamed of adding to my collection. Due to its price and relative scarcity in the U.S., it's always been out of reach for me until this past few years.

 It wasn't until I looked at an online camera auction that I found the Welta Superfekta at a price that was not only reasonable but also inexpensive. Online, the camera looked in good to decent condition, but they said the shutter was erratic. To me, those words mean I'll need to send the camera in for a shutter repair, which isn't too uncommon for a camera reaching 100 years old. 

 I purchased the Welta Superfekta online, and when the camera arrived, as suspected, its shutter was extremely sluggish and needed to be CLA'd. I reached out to the person I usually send cameras for servicing, and he confirmed he could service the shutter but wasn't sure about other areas of the camera, as he wasn't too familiar with it.

The excitement of adding the Welta Superfekta to my collection was wonderful, especially since it's a 6x9 cm-format camera that takes 120 film. Still, the more exciting part of the camera is that it's very similar to the Cornu Ontoflex, which has a rotating back, allowing the photographer to shoot both vertically and horizontally without turning the camera sideways. Just rotate the back from vertical to horizontal and flip the image orientation, as with the Mamiya RB67.

 The one thing I noticed when I turned my camera from vertical to horizontal is that the back doesn't turn all the way, which makes me curious about its history. This flaw, while concerning, adds character and a story to the camera, resonating with collectors who appreciate Imperfections.  

Another reason for my excitement to add the Welta Superfekta to my collection is that it would be the third folding Twin Lens camera in my collection. I had already purchased and written about both the Welta Perfekta and the Zeh Zeca-Flex cameras, making this the “Trifecta” of this camera style.

Welta Superfekta, Perfekta and Zeh Zeca-Flex camera.

Welta before World War II:

 The history of Welta Kamerawerke leading up to World War II is a testament to the rapid innovation and high-precision craftsmanship that defined the German photographic industry in the early 20th century. Founded in 1914 by Walter Waurich and Theodor Weber in Freital, near Dresden, the company began as "Waurich & Weber" before adopting the "Welta" brand name that would eventually become synonymous with high-end folding cameras.

French ad for the Welta Perfekta and Superfekta cameras

 In its first decade, Welta focused on the transition from heavy glass-plate cameras to the more versatile roll-film formats. By the 1920s, Freital and the surrounding Dresden area had become the global epicenter of camera manufacturing, and Welta held its own against giants like Zeiss Ikon. Their early success was built on the folding camera—a design that allowed a high-quality lens and shutter to collapse into a slim, leather-covered metal body.

 The 1930s marked Welta's "Golden Era." During this decade, the company moved beyond standard designs to create some of the most mechanically complex cameras ever made. While competitors were focusing on the emerging 35mm trend, Welta mastered the 120 roll-film market with innovative models like:

 

  • The Weltur: A rangefinder folding camera known for its incredible build quality and integrated viewfinders.

  • The Perfekta and Superfekta: These folding Twin Lens Reflex (TLR) cameras were engineering marvels, offering the ground-glass focusing of a studio camera in a portable, collapsing frame.

  • The Welti: A foray into the 35mm market that proved Welta could compete with the Leica in terms of precision and optics, often featuring high-end Carl Zeiss Jena or Schneider lenses.

 Welta's pre-war philosophy was to offer a variety of price points without sacrificing mechanical integrity. You could find a simple Welta Trio for the casual hobbyist, or a Superfekta with a rotating back for the professional who demanded perfection. This versatility allowed Welta to export heavily to the UK and the United States, where their cameras were often rebranded for local retailers.

 By the late 1930s, Welta was a premier name in photography. However, as Germany shifted toward a war economy, production began to pivot away from consumer optics. After the war, Freital was part of the Soviet occupation zone (later East Germany), and Welta was eventually absorbed into the state-owned VEB Pentacon, marking the end of its era as an independent, family-founded innovator.

My Camera:

 My Welta Superfekta camera is 7.5" tall without the light chimney opened, and 10" with it opened, by 4" wide, and 3.5" deep with the body retracted, and 6.25" deep when the body of the camera is extended. The camera weighs 3 pounds, 0.2 ounces without film, so it has some heft.

To extend the camera body away from the film chamber, press the silver button on the right side of the camera body, located just below the film winding lever. Pressing the button quickly extends the camera lens area, and you'll be able to see the bellows. By doing so, you'll see how the camera gets its name, a folding twin-lens camera. When I extended the camera's front from the rear, I noticed the bellows were in excellent light-tight condition.

 My camera has a 7.5cm f/3.5 Weltaskop viewing lens, along with a Carl Zeiss Jena 10.5 F/3.5 Tessar taking lens, so the viewing lens is wider than the taking lens, and the taking lens is in a Compur-Rapid shutter with shutter speeds from 1/400 to 1 sec. along with "B", and "T". The focus lever is located on the left side of the lens when you're holding the camera, and it slides up and down to focus on your subject. 

There is also a focus scale along the top of the camera, between the Welta sign on the film body and the Superfekta sign on the lens area. As you slide the focus lever up and down, you'll see a triangle move from side to side, indicating the distance to the subject on the focus scale, which is in meters.

 Along the back of the camera, by the viewfinder, there is a button to press to open the light chimney. The light chimney popped up, and along one side is a depth-of-field scale for the camera, and on the front is the magnifying lens, which flips as it should. 

On the back of the film body is another sliding lever that you move to the left, in the direction of the arrow, and the back will open. Opening the back of the camera, I noticed that the film advance roller, which activates the frame counter, is missing, so the frame counter isn't operational on this camera. Luckily, there is a red window on the back door so you can see the numbers being transported as you roll the film from one image to the next. 

 I also noticed a paper sign glued to the inside of the back door at the top, which read, "non si girare il rullo che nel senso della freccia" (translation from Italian to English: "do not turn the roller in the direction of the arrow").  This message on the inside tells me the camera is originally from Italy. I guess the camera was made for the Italian market, but the reseller may have added that; I'm not certain. Still, it's interesting that a German camera was sold in Italy and found its way to the USA.

To load the camera with film, the chamber where you put in a fresh roll of film pulls up to make it easier to put in the film, which is a nice feature in the camera. Otherwise, the camera loads just like many roll film cameras, but it would have been nice to have a frame counter that advances from the roller on the back to indicate the frame numbers. I'll just have to do it the "old-fashioned" way and look through the red window to get to the next frame when I shoot.

To collapse the camera lens area into the camera body, you'll need to press in two silver buttons on the front of the camera, placed between the viewing and taking lens, and press the lens area into the film body, which is extended by a couple of scissor struts on each side of the camera. Be sure to retract the camera stand leg, under the front lens area, just behind the tripod socket, before closing the camera. If you don't do this, the camera will not close. I know because I've tried a few times by accident.

 When you close the camera, another interesting thing is that there's a roller at the tip of the film area on the outside. When you close the lens into the film body, the viewfinder rolls along the roller, sliding it forward and covering the focus scale. Given that the camera is almost 100 years old, it's still interesting how it opens and closes mechanically. 

If you don't want to rotate the film chamber when shooting, there is a flip-up sports-type finder on the side of the camera you can use if that's easier for taking horizontal images. It just gives the photographer another option when using the camera.

 

My Results:

 I don't have a case that fits my Welta Superfekta camera. The camera doesn't have the standard loops you can snap into a carrying strap, so when I went out shooting a few times, I just put it in a pouch-style case to carry it and took it out when I was ready to shoot.

 Looking at the side of the camera, there are a couple of studs and other areas where a strap might fit, but without a manual or a nomenclature for the items on the camera, I'm unsure what they are used for.

 I took the Welta Superfekta out a couple of times to shoot with: once to a local lake and another time while walking around the neighborhood to get closer-up images.

 Here are the results from my two times using the camera.

Conclusion:

 The camera's results underwhelmed me, as one of two things is happening. First, I didn't think the images would be as sharp as I had imagined; that may be because something happened to the camera, like a drop or impact, which is also why the camera doesn't flip all the way horizontally when shooting. 

 My weakening eyesight may also cause it, but because of eye surgery I had last year on my right and dominant eye, I'm becoming more and more dependent on using my left eye for focusing, which is difficult for me at times. Personally, I feel it's more the first issue: something tweaked the camera body, and the lens doesn't align properly, which is why I wanted to shoot the second, more close-up images walking through the neighborhood.

 Nonetheless, it's somewhat awkward to hold without a neck strap to keep it steady. Still, I absolutely love the camera's ability to rotate the film back for both vertical and horizontal photography. It's a wonderful camera to have in my collection, and for the price paid, even with the servicing, it's still a bargain.

Welta Perfekta and Superfakta side views

 Thank you for taking the time to learn about this wonderful photographic marvel from almost 100 years ago.

 Here's a link to my other Camera Reviews.

 Cuny's Cameras and Photo is my online eBay store, which sells some of the cameras reviewed, along with many camera and photo accessories.

 Until next week, please be safe.