My Rapid Omega 200 camera.
The last time I owned a Rapid Omega was many years ago. Still, when I saw one online with an extra back for a very reasonable price, I was interested but skeptical that the camera might have issues, which is somewhat common for a camera 50 years old or older.
The price was too good to pass up, and if the camera was bad or the lens had issues, I could always resell it for parts and still make a bit on the deal. I pulled the trigger and bought the camera, and when it arrived, it was in much better condition than expected.
The shutter fired, and the lens and backs were in good, clean condition. The rangefinder was bright, clean, and accurate. I kept thinking there must be something wrong with the camera. Still, until I put film in the camera, the only thing that was wrong with the camera was the operator, which I'm embarrassed to say.
It's been 3 months since I bought the camera, and my initial intention was to shoot and write about it. Now it was time to put the camera through its paces, so I took the back off, opened it, and loaded film into one of the film backs. I put the back onto the camera body. I walked through the neighborhood, taking photos of the usual items I shoot when I take a camera out, so readers can reference similar items if they want to compare.
I can still remember thinking, as I took the photos, how much I liked the camera. The rangefinder was bright and easy to focus, bringing the two images into one, and they seemed so large. The whole time, I thought these images would be nice, and the camera handled so well. What a wonderful camera; it also took 6x7cm images, similar to the Mamiya RB67 or the Honeywell/Asahi 67 cameras, which seemed more awkward to shoot.
I got home, took the film out of the camera, and loaded the film into my film processing tank. At this point, I was filled with anticipation and excitement to see how the camera handled the different items I photographed. After I cleared the fixer from the tank and started the wash cycle, I always take a peek at a few of the last images to make sure there were images on the film.
To my amazement, the film was totally clear, but I could still see the rebate numbers. What happened? No light was reaching any of the images I took, yet I knew the shutter was opening and closing.
I looked at the camera, puzzled. As I twisted the camera around to look at all the different parts, I noticed the dark slide on the film back was in the holder, and my thought went to, "I forgot to remove the dark slide before taking photos." What a rookie mistake, but at least I know that won't happen again.
No, that wouldn't happen again, but something just as idiotic will.
Throwing the newly processed and blank film in the trash, I proceeded to load the film back again with another roll of film, putting the back on the camera body, and NOW, taking the dark slide from the back, I proceeded to walk the same path as I did about an hour earlier, taking the same approximate images as I did before, as they were fresh in my mind.
As I walked back to the house to process the second roll of film I shot within about an hour of the first, I looked down at the camera. I did something even more embarrassing than the first time. I forgot to take the lens cap off before shooting another 10 images.
OH MY GOD!!!! What an idiot, is all I kept thinking.
I guess the good news is I didn't spend the time and effort processing this new blank roll of film. So at this point I guess I could have taken the film into my dark bag and re-rolled it back onto a blank spool. Still, I was so frustrated and mad at myself that I decided to take the rest of the day off and do something else before I loaded another roll of film into the camera and tried for the third time.
The next day, the sun was shining, so I put the third roll of film into the film back, attached it to the camera body, double-checking that 1) I took the dark slide out from the film back, and 2) I took the lens cap off and put it in my pocket for safekeeping. Retracing most of my steps, and with a new calmness to my photography, I took the roll of film knowing full well that these images would turn out in wonderful condition.
After processing the third roll of film and looking at a few images before doing a full wash on the negatives, I saw the results. I breathed a sigh of relief, knowing the camera worked well and that the previous issues were operator malfunctions.
I now fully understand why other cameras have 'foolproof' methods built in—a dark slide that's supposed to lock the shutter so you can't take a photo with it still in place. The second error could happen with many different cameras, especially rangefinder cameras where you're not looking through the lens. Well, at least the images turned out well, and from looking at the images below, the camera did a wonderful job.
History:
The Rapid Omega 200 is one of those cameras that looks like it was built to survive a war. It's a big, heavy 6x7 rangefinder, and it's the last in a line that started in 1954.
The story starts with the Simmon Brothers in New York. They were known for their darkroom enlargers, and in 1954 they built the Omega 120, a 6x7 rangefinder with a fixed 90mm f/3.5 lens. It was designed to work fast — a press camera, really — and the film was advanced by pulling and pushing a metal strip on the back of the camera. That pull-push advance is where the "Rapid" in the name comes from.
An advertisment for an earlier Koni-Omega Rapid camera from 1967
Simmon merged into Berkey Photo in 1961, and not long after, the design was licensed to Konica in Japan. Konica built the line as the Koni-Omega, starting with the Rapid in 1964 — sold in Japan as the Konica Press — and the Rapid M followed in 1968 with interchangeable film magazines, so you could change film mid-roll. The lenses were Hexanons: a 90mm f/3.5 standard, a 58mm wide-angle, a 135mm, and a 180mm, all with leaf shutters up to 1/500.
In the mid-1970s, Mamiya took over production in the same factory, and the cameras came out in an all-black finish under the Rapid Omega name. The Rapid Omega 100 and 200 arrived in 1975, and the 200 was the top of the line—the Rapid M, with an interchangeable magazine and dark slide for swapping film mid-roll. The 100 couldn't do that, since its magazine front was fixed to the body.
The 200 shoots 6x7 on 120 film: ten shots per roll, or twenty on 220. It has a coupled rangefinder with automatic parallax compensation, framelines for the 90, 135, and 180mm lenses, and the wide angles need an external finder. The standard lens by then was called the Super Omegon 90mm f/3.5. The whole camera weighs about four and a half pounds with the normal lens — built like a tank.
Wedding photographers loved these cameras in the 1970s because they were fast. You could shoot candid after candid, and the lenses were first-rate. But by the late 1970s, 35mm cameras and 120 SLRs were taking over, and the press camera was on its way out. Production ended in 1981.
That's what I like about the Rapid Omega 200. It was the last of the true press cameras — big, heavy, and built to work fast.
My Camera:
The Rapid Omega 200 is 10" wide with the accessory handgrip and the winding mechanism on the film back, and 5.5" tall and 6" deep when the 90mm lens is focused at infinity. My camera body serial # is 64882, and the 120 film back serial # is 115744. A 220 film back was also available for this camera.
The camera has a Super Omegon 90mm f/3.5 lens, serial #711534, with an internal leaf shutter and shutter speeds ranging from 1 sec. to 1/500, along with "B". The aperture range is from F/3.5-22. Both the shutter speed and aperture settings are done by individual rings located at the end of the lens. The lens also has a pull-out hood that, when pulled out, reveals the depth-of-field scale, but you need to set the distance manually by turning the ring to the desired distance.
To remove the lens from the camera body, there is a black lever on the lower right side of the camera body with "lock" written on it; turning it opposite the "lock" arrows unlocks the lens and allows you to change lenses. This camera had 4 lenses: 58mm, 90mm, 135mm, and 180mm. To put the lens onto the camera body, make sure the squared area on the lens, which has a pin on the inside, fits into the hole just under the "Rapid Omega" nameplate, and turn the locking lever in the direction of the "lock" arrow until you hear a slight "click". The lens is now attached to the camera body.
The camera, lens, and film back make for a somewhat big, bulky setup. Still, with the accessory handgrip and left-side hand strap, it becomes manageable and easy to use. The grip has a cable release. Still, for me it's just as easy to press the shutter release on the upper left side of the camera body without it, so I don't attach it to the grip when I'm using the camera.
There are three (I don't know why three) accessory shoes on the top of the camera. Looking at the Rapid Omega 200 manual (Thank you, Mike Butkus), there seems to be only 1 accessory finder, a sports finder, as the viewfinder on the camera has lines for the other lenses available for framing purposes. I find this a bit odd.
You focus the Rapid Omega with a bright, large rangefinder in the upper-left corner on the back of the camera. A large focus knob on the right side of the camera lets you turn the two images together in the rangefinder. It was easy to hold the camera in my left hand and focus with my right, making the camera very balanced and easy to handle. The rangefinder is parallax-corrected too, so the closer you focus, the more "true" it is to the image you'll get on the film.
To take the film back off the camera, the chrome " lock " lever behind the lens is a "lock" lever on the camera body. Slide the lever counterclockwise with the thumb lever, making sure the dark slide is in the film back, and the film back will disengage from the camera body. Remove the back from the camera.
Here's the proper film loading on the Rapid Omega 200 camera:
1. Set the counter to LOAD. The frame counter should read LOAD. If it doesn't, pull the film transport knob all the way out and back in until it does. If the transport is locked at 10 (end of a 120 roll), push up on the film transport release while working the knob until LOAD appears.
2. Open the film back. Press the film-type tab holder release so the holder springs open. Lift the key on the film back lock and turn it until "O" lines up with the white dot.
3. Lift the back off. Don't pull on the key — hold the back in your left hand and lift it out by its sides.
4. Move the empty spool to the take-up side. Push slightly up on the upper feed spindle to free the empty spool, then place it on the take-up spindles, making sure the key on the lower take-up spindle engages the spool's keyway. Rotate it with your thumb until the long slot faces the feed spindles.
5. Load the fresh roll. Place it on the feed spindles with the seal unbroken, oriented so the black inner face of the leader faces you when unrolled. Break the seal and remove it.
6. Thread the leader. Unroll enough paper leader to slip the end into the take-up spool slot, then rotate the take-up spool with your thumb to take up the slack.
7. Wind to the start mark. Press lightly on the film roll with one thumb while rotating the take-up spool with the other. Keep the film perfectly centered and taut, and keep winding until the start arrows on the backing paper line up with the red film start mark on the take-up spindle, near the transport knob.
8. Seat the back. Make sure the back lock is still at "O", then lower the back gently into the magazine — don't force it.
9. Lock it. Turn the back lock key to "L", fold it flat, and close the film-type tab holder. Then pull gently on the sides of the back to confirm it's locked in.
10. Advance to frame 1. Pull the transport knob fully out and back in — one green dot appears in the counter. Repeat: two green dots on the next stroke, then "1" on the third. That's the first frame, ready to shoot.
Putting the film back is a bit tricky, as you need to make sure the small tab on the dark slide is pointing outwards when you reattach it to the camera body. If the tab isn't facing outwards, the back won't seat properly onto the camera body, and you cannot lock it back on.
Once attached and after you've taken a photo, I like the film advance lever. Sliding the large knob in and out of the film back is smooth. It's easy to use, albeit unconventional compared to other camera transport systems.
I got rather proficient at loading the camera, especially since I went through two rolls of film before I finally put in a roll that produced images.
My Results:
Well, finally. After my mishaps with the camera, and again, all operator malfunctions, I finally got images from the third roll I put through the camera, and they were better than I expected. The camera did a wonderful job.
Here, have a look at the images I took with the third roll of film I put through the camera.
Conclusion:
The camera did a wonderful job. It was well balanced, the focus was bright and easy to use, and once I finally got images, they were sharp, well composed — just a wonderful camera to use.
There were some items that were a bit difficult. The dark slide is a bit difficult to remove once the film back is attached to the camera. It was difficult for me to grab onto the dark slide tab and pull it out, and making sure the pull tab on the dark slide was pointing forward when attaching it to the camera body was a bit frustrating at first, but once I figured it out, it was OK.
While the camera has its quirks, as all cameras do, once I figured out my shortcomings with the camera, I enjoyed it. I'm unsure if I'll be keeping this camera in my collection, as you'll most likely see the camera on my eBay store in the not-so-distant future, as I originally purchased it for my blog and fully intended to sell it once I do write about it.
Thank you for taking the time to read about the Rapid Omega 200 camera that I recently added to my collection.
Are you interested in other vintage gear? Here are some of my other Camera Reviews.
Check out my Cuny's Camera Collection YouTube channel, where I am putting together video overviews of the cameras I write about. Be sure to subscribe and like the channel, too!
Cuny's Cameras and Photos is my online eBay store, where you will find some of the cameras I have reviewed, along with a wide range of other cameras, lenses, and items from my collection that I am thinning out.
Until next week, please be safe.